Detailing, Protective Coatings & Waxes

SPACE AGE PROTECTION FOR YOUR CAR, TRUCK, BOAT, RV, AIRPLANE & MOTORCYCLE RejeX® is a thin-film polymer coating designed to provide a high-release protective finish for vehicles of all kinds. This very thin film – less than a micron thick – prevents stains and adhesion of common contaminants such as exhaust, bugs, oil, tree sap, bird droppings, road grime, brake dust, etc. NOTHING STICKS BUT THE SHINE!™ It also makes graffiti easy to remove and can be applied to windshields to repel rain. It’s easy to apply and produces a deep, lustrous shine that outlasts the most popular waxes by months. RejeX contains none of the free silicone oils found in some other products that are known to contaminate paint and cause problems when repainting. REJEX APPLICATION Ideally, RejeX should be applied to a cool, dry, clean surface. When over 85° F, be sure to apply RejeX out of direct sunlight. If the surface is too hot, the coating can cure before it has properly bonded to the surface, so it may not perform up to its potential. RejeX is wiped on, allowed to dry to a haze for approximately 20 minutes, wiped off, then allowed to cure for 8-12 hours (depending on the humidity; the higher the humidity, the faster the cure). Curing is required to allow the monomers (polymer building blocks) that make up RejeX to attach to the surface being treated and to cross-link into a crystal-clear, impervious film. It is important to allow RejeX to cure for 8-12 hours after the haze has been wiped off. If the coating is exposed to contaminants such as oil, fuel, soot, hard water, tree sap, cleaners, etc. before it has cured, the contaminants may interfere with or embed in the protective film.   REJEX PROTECTS AND BEAUTIFIES PAINTED METAL, GLASS, ACRYLIC, GEL COAT, FIBERGLASS, GLOSSY PLASTIC & POLISHED METAL SURFACES RejeX is not meant to be used on porous surfaces, highly oxidized painted surfaces, or to fill fine scratches. RejeX can be applied in multiple coats, allowing 8 hours curing time between coats for deeper color and greater depth of gloss. RejeX has a higher refractive index than waxes, so it produces richer, deeper looking colors and a lustrous long-lasting finish. RejeX can be used over existing wax; however, the duration of protection will be reduced as the softer underlying wax degrades comparatively quickly. There is no reason to wax over RejeX. As already stated, RejeX leaves a shinier, longer-lasting finish than wax… and waxes will have difficulty adhering to RejeX! If a RejeX-treated surface needs repainting, normal paint preparation is all that’s required. Abrasive cleaners, polishes, rubbing compounds and some chemical paint strippers can remove RejeX. National Stock Numbers RejeX 16 fl oz NSN 8030-01-593-8208 RejeX brochure | RejeX FAQ

MUD SLIDE gives race teams the advantage both on the track and in the pits. Using MUD SLIDE as directed will keep mud, oil and exhaust from clinging to your racing body panels, underbody, suspension components and graphics. As an added bonus, MUD SLIDE is formulated using naturally occurring plant and vegetable oils and extracts, making it a more environmentally preferable choice. Designed to be applied with a single, ultra-thin coat, MUD SLIDE is non-staining and makes vehicle cleanup exponentially easier.   Premium ingredients ensure the highest possible ease of mud release fromvehicles and components Great for race cars, commercial off-road vehicles, ATVs and UTVs MUD SLIDE’s ultra-thin film does not induce any drag that might otherwise adversely affect aerodynamic performance Will not stain or discolor High purity product will not clog spray nozzles   "Tried out a new product last night. I sprayed Mud Slide on the car and then sent it out to pack the track and hot lap. It came back in nice and muddy, and I was able to wipe the mud right off! Usually I have to peel the wet mud off or let it dry and then knock it off. But with Mud Slide, I was able to do a fast easy clean off as soon as the car came off the track."     "Thank you to everyone that came out in the heat to support. Also got to try our Mud Slide to help with the mud. Looks like it's going to be a great product to have in the trailer. ... Get your order in." – Chip Graham Racing         "So there is a NEW PRODUCT out on the market made by CorrosionX caled Mud Slide. This stuff is amazing! After hot laps came in with very little mud on the car, grabbed a rag and started wiping. The mud came off instantly without streaks or smears. Hands down I will be keeping a bottle in the trailer to use week in and week out! It's by far the best product I've found and a little bit goes a long way." –  Nick Stewart   "Spray it on your car like you do baby oil or mud off and it makes the mud fall off. Well the track was plenty wet for sure so we damn sure put it to the test and i will admit this stuff work amazingly good! Both cars came off the track nasty and the mud just fell right off. Highly recommend trying this stuff out!" – John Ricketts               "I love it, my crew loves it, your mom loves it. Make your mud scraper’s day and your sponsors happy." –  James Broty

MULTI-SURFACE PRESERVER / UV PROTECTION Shine & Shield™ was developed to clean, protect and preserve vinyl and rubber surfaces. The product shields against sun damage (ultraviolet spectrum), cracking, weathering and fading. It will not cause vinyl graphics to fade or crack. Great for use on dashboards, tires, weather-stripping, hoses, rubber window molding, outdoor vinyl seats and outdoor furniture. Great For: Automotive Recreational Vehicles Commercial Vehicles Boats Aircraft

ONE-STEP DRY WASH, POLISH & FRICTION REDUCER Aero-Glide™ waterless dry wash is specially formulated with a blend of deep cleaners and light oxidation removers to provide a true one-step cleaning, detailing and polishing solution that leaves a high gloss protective finish on aircraft and other vehicles. Aero-Glide's hard protective coating reduces surface friction and adhesion of exhaust stains. Easy on, easy off No water necessary No need to pre-clean vehicle prior to use Removes light surface oxidation on most finishes Provides mid-term (approximately 3-4 month) protection against UV, exhaust soot and other grime Meets Commercial Aviation Certifications ASTM F484-008 (2013)ASTM F519-13AMS 1650CASTM F502-08 (2013)BOEING D6-17487 Rev. P | Tech Sheet |

MULTI-SURFACE INTERIOR / EXTERIOR SPRAY AND WIPE FOAMING CLEANER 5 Star Foam™ rates as the absolute finest foaming cleaner in the industry! 5 Star Foam is for use on interior smudge marks, nicotine stains, oily fingerprints and food stains. On aircraft exteriors, 5 Star Foam will effectively clean carbon exhaust, oil and bugs. It can also be used on vinyl, leatherette, plastic, sinks, enameled, varnished and similar surfaces. 5 Star Foam was designed specially for hard to remove grease and soil unaffected by other cleaners. Its clinging foam permits long-lasting contact with irregular, as well as plain, surfaces to be cleaned. Its high pressure spray enables it to reach hard-to-get-to trouble spots. Meets or exceeds the scope and performance requirements of MIL-C-878937 Type II Passes ASTM-F-484 Type A Stress Crazing Of Acrylic PlasticSuitable for use on BOEING LEXAN 9600 and GE-MR5 LEXANPasses ASTM F502, Standard Test Method for Effects of Cleaning and Chemical Maintenance Materials on Painted Aircraft Surfaces RECOMMENDED FOR USE ON: Aircraft and boat exteriors Tile Sinks Tubs Stainless Steel Vinyl Plastic Surfaces

ANTI-STATIC PLEXIGLAS CLEANER, PROTECTANT AND POLISH A-Plex™ is an anti-static aircraft and marine Plexiglas cleaner, protectant and polish. Also excellent for use on motorcycle windscreens. A-Plex produces a microscopic, high luster, soil retarding and water repellent finish to aircraft and marine plexiglass – leaving a surface that is lustrous. A-Plex dries with no smears, no smudges and no oily residue. Can be applied in seconds. Specifications Meets or exceeds the scope and performance requirements of MIL-C-878937 Type II Passes ASTM-F-484 Type A (stress crazing of acrylic plastic) Suitable for use on BOEING LEXAN 9600 and GE-MR5 LEXAN Passes ASTM F502, Standard Test Method for Effects of Cleaning and Chemical Maintenance Materials on Painted Aircraft Surfaces

PNEUMATIC DE-ICING BOOT SEALANT, UV AND WEAR PROTECTANT Boot Sealant is Step 2 in maintaining and properly protecting the surface of pneumatic de-icing boots. Corrosion Technologies Boot Sealant prevents drying and cracking by sealing and protecting de-ice boots from harmful UV rays. Simply apply Boot Sealant to your de-icing boots with a soft cloth, and when dry, Boot Sealant stays slick and shiny for months! To prepare your de-ice boots for a treatment of Boot Sealant, it is important to first clean them and remove old, residual sealant by using Corrosion Technologies' Boot Klean™.

THE QUICK DETAIL SPRAY THAT CLEANS AND SHINES LIKE MAGIC! RefleXion™ returns aircraft, boats, cars, RVs and motorcycles to that 'just detailed' look between regular washing and waxing (or RejeX-ing). Quickly and easily removes dust, road film, fingerprints, streaks and water spots safely from most vehicle surfaces. Cleans and shines all hard surfaces – just like magic! High lubricity formula picks up dirt and dust without scratching Removes harmful contaminants such as exhaust, bug splats and bird droppings Enhances shine Clean your whole vehicle in the time it would take to drag out the garden hose, bucket and car wash soap

CARPET SPOT AND STAIN REMOVER 5 Star Stain Remover™ was formulated to be a powerful, easy-to-use carpet and cloth stain remover. It's the quick and easy solution for removing grease, oil and ground-in dirt. May be used on most types of carpet Excellent for pre-treating stains prior to carpet shampooing Add to your existing carpet shampoo to boost cleaning power Contains biodegradable surfactants Will not harm plastic RECOMMENDED FOR USE ON: Car and truck carpet Commercial carpet cleaning Pretreating high traffic area soils Removing grease and oil spots Tough stains like red wine and cofee

PROFESSIONAL GRADE DRY WASH & WAX This specially formulated, carnauba-enriched waterless dry wash and speed wax is designed to clean and provide short-term, high gloss protection for vehicle finishes – all in one step! Xtreme Finish™ can also be used as a cleaner and detailer between RejeX® treatments. Easy on, easy off No water necessary No need to pre-clean vehicle prior to use Increases gloss and adds warmth to vehicle finishes Provides short-term (approx. 1 month) protection against UV and road grime Great For: Cleaning vehicles without soap and water Removing light dust and road grime Cleaning and detailing between RejeX treatments Adding warmth, richness and additional gloss to your vehicle's finish

MULTI-FABRIC FOAMING CLEANER Velour and Leather Upholstery Cleaner cleans and removes lipstick, dirt, grease, hand prints, pencil marks and grime from most leather, velour, vinyl, plastic and canvas materials. The thick foam clings to all vertical surfaces, while the foaming action penetrates deep to all kinds of dirt, grease and grime. Recommended for use on most fabrics, including: Velour Leather Plastic Vinyl Canvas